現在有一大堆軟路由系統
https://en.wikipedia.org/wiki/List_of_router_and_firewall_distributions，都不知道那個好，那個不好。
這么多系統，也不可能一個一個去安裝測試，那不如自己試試用 Ubuntu 設置一臺路由。
硬件（迷你電腦）：
- Intel n3150 CPU, 4GB RAM, 64GB SSD
- Realtek Giga LAN x 2
- Intel N-7620 Wireless LAN x 1
軟件系統：Ubuntu Server 16.04.2 LTS
Ubuntu 系統的安裝，SSH 的安全設置（禁止密碼登錄，4096 bits key）等就不詳細說了。
以下內容包括：
- 修改 Network Device Name
- 創建 bridge, br0 （eth1 + wlan0）
- 設置無線 Access Point （hostapd）
- 安裝 DNSmasq 作為 DNS 和 DHCP 服務器
- iptables rules (firewall + Port Forwarding)
- DDNS
- overlayroot
- 其他腳本
- WAN-to-LAN 速度測試
1. 修改 Network Device Name
Ubuntu 從前一兩個版本開始，網卡的名稱就不是 eth0, eth1, wlan0 等，使用起來很不習慣。所以第一步是把它們改回原來的命名方式。
創建一個檔 ：
/etc/udev/rules.d/70-persistent-net.rules
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="xx:xx:xx:xx:xx:xx", ATTR{dev_id}=="0x0", ATTR{type}=="1", NAME="eth0"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="xx:xx:xx:xx:xx:xx", ATTR{dev_id}=="0x0", ATTR{type}=="1", NAME="eth1"
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="xx:xx:xx:xx:xx:xx", ATTR{dev_id}=="0x0", ATTR{type}=="1", NAME="wlan0"
上面 "xx:xx:xx:xx:xx:xx" 是每張網卡的 mac 地址（可以用 ifconfig -a 來查詢）
（不要忘了）然后修改 /etc/network/interfaces，將里面的網口名稱改回 eth0，eth1，wlan0，存檔，重啟...
重啟后三張網卡的名稱已經改變 。這三張網卡將會如此使用：
- eth0 - WAN
- eth1 - LAN （10.0.1.1）
- wlan0 - LAN （10.0.1.1）
2. 創建 bridge, br0 （eth1 + wlan0）
就如一般的路由，我希望 eth1 和 wlan0 共用一個 LAN 地址，就如一張網卡般使用。
1
apt-get install bridge-utils
修改 /etc/network/interfaces:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
#auto eth0
allow-hotplug eth0
iface eth0 inet dhcp
iface eth1 inet manual
iface wlan0 inet manual
# Bridge setup
auto br0
iface br0 inet static
bridge_ports eth1 # wlan0 added by hostapd "bridge=br0" line.
address 10.0.1.1
broadcast 10.0.1.255
network 10.0.1.0
netmask 255.255.255.0
gateway 10.0.1.1
bridge_stp off # disable Spanning Tree Protocol
bridge_waitport 0 # no delay before a port becomes available
bridge_fd 0 # no forwarding delay
bridge_ports 只需要 eth1 就行，wlan0 會經 hostapd 加入到 br0 里面。
3. 設置無線 Access Point （hostapd）
apt-get install hostapd haveged
haveged （看這里）非常重要。沒裝它的時候，無線終端（例如：手機）連上接路由后能正常使用。但當路由重啟后，手機就會出現“身份驗證錯誤”，然后自動忘記無線密碼。我花了四五個小時 google，修改 hostapd.conf，甚至換無線網卡測試。后來才找到原因。不明白 Ubuntu 官方連 overlayroot 都預裝了，卻不預裝 haveged。而且大部分的 hostapd 教程也沒有提到 haveged。
返回正題。修改 /etc/default/hostapd：
DAEMON_CONF="/etc/hostapd/hostapd.conf"
創建 /etc/hostapd/hostapd.conf :
interface=wlan0
driver=nl80211
bridge=br0 # Add wlan0 to br0
country_code=HK
ieee80211d=1
ctrl_interface=wlan0
ctrl_interface_group=0
ssid=YOUR-SSID
hw_mode=g
channel=6
wpa=3
wpa_passphrase=YOUR-PASSPHASE
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP
beacon_int=100
auth_algs=3
macaddr_acl=0
eap_reauth_period=360000000
ignore_broadcast_ssid=0
# enable 802.11n (n-mode)
ieee80211n=1
wmm_enabled=1
4. 安裝 dnsmasq 作為 DNS 和 DHCP 服務器
apt-get install dnsmasq
修改 /etc/dnsmasq.conf
interface=lo,br0
dhcp-range=10.0.1.21,10.0.1.250,255.255.255.0,12h
cache-size=500 # 緩存多少個地址，按需要修改
DNS 服務器方面，我除了 dnsmasq 外，我還裝了 dnscrypt-proxy 防止 dns 劫持 （dns 污染）。但這帖子已經很長，所以這里不寫了。
現在重啟路由后，手機等終端可以連接上路由了，可是還是不能上網。因為還缺少了下一步的 MASQUERADE。
5. iptables rules (firewall + Port Forwarding)
Debian/Ubuntu 的 iptables 教程，都是在 /etc/network/if-pre-up.d 里面加一個腳本來啟動 iptables 規則。因為我的 Port Forwarding rules 使用到 WAN 口的 地址，所以我把 iptables 分成 if-pre-up.d 和 if-up.d 兩部分。pre-up 時（eth0 還沒 ip 地址 ）啟動 firewall filter 等，post-up 時（eth0 已經分配到 ip 地址）加上 port forwarding 規則。
if-pre-up.d 部分，創建
/etc/network/if-pre-up.d/my-pre-up :
#!/bin/sh
EXTIF=eth0
if [ "$IFACE" = "$EXTIF" ]; then
/bin/sh /usr/myscripts/iptables/pre-up-rules
fi
創建
/usr/myscripts/iptables/pre-up-rules：
#!/bin/sh
EXTIF=eth0
INTIF=br0
LOG=/tmp/set-rules-router.log
WANIP=$(/sbin/ifconfig $EXTIF | grep 'inet addr:' | cut -d: -f2 | awk '{ print $1}')
echo "PRE-UP : `date`" | tee -a $LOG
echo "$IFACE pre-up, $EXTIF IP : $WANIP" | tee -a $LOG
echo | tee -a $LOG
SSHPORT=22222;
echo "Setting default policy and clearing all rules ..." | tee -a $LOG
# Default poliicy
/sbin/iptables -P INPUT DROP
/sbin/iptables -P OUTPUT ACCEPT
/sbin/iptables -P FORWARD DROP
/sbin/iptables -F
/sbin/iptables -X
/sbin/iptables -t nat -F
/sbin/iptables -t nat -X
/sbin/iptables -t mangle -F
/sbin/iptables -t mangle -X
/sbin/iptables -t raw -F
/sbin/iptables -t raw -X
echo "Setting up firewall rules..." | tee -a $LOG
# Ref : https://wiki.debian.org/DebianFirewall
echo -n '1' > /proc/sys/net/ipv4/ip_forward
echo -n '0' > /proc/sys/net/ipv4/conf/all/accept_source_route
echo -n '0' > /proc/sys/net/ipv4/conf/all/accept_redirects
echo -n '1' > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
echo -n '1' > /proc/sys/net/ipv4/icmp_ignore_bogus_error_responses
# Chains :
/sbin/iptables -N syn_flood
## Protection 1 vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
# Openwrt : Drop XMAS, Null first, then invalid packets (these 3 come before other rules)
#
# XMAS packets
/sbin/iptables -t raw -A PREROUTING -p tcp -m tcp --tcp-flags ALL ALL -j DROP -m comment --comment "Drop XMAS packets"
# Drop all NULL packets
/sbin/iptables -t raw -A PREROUTING -p tcp -m tcp --tcp-flags ALL NONE -j DROP -m comment --comment "Drop all NULL packets"
##^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
# Enable loopback traffic
/sbin/iptables -A INPUT -i lo -j ACCEPT
# Enable statefull rules (after that, only need to allow NEW conections)
/sbin/iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT
/sbin/iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT
# eth0 - WAN, eth1 - LAN, this will allow your internal to access the external:
/sbin/iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE
/sbin/iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT
# DNS - accept from LAN
/sbin/iptables -A INPUT -i $INTIF -p tcp --dport 53 -j ACCEPT -m comment --comment "Accept DNS from LAN"
/sbin/iptables -A INPUT -i $INTIF -p udp --dport 53 -j ACCEPT -m comment --comment "Accept DNS from LAN"
## Protection 2 vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
# Drop Invalid Packets
# Drop invalid state packets
/sbin/iptables -A INPUT -m conntrack --ctstate INVALID -j DROP -m comment --comment "Drop Invalid INPUT Packets"
/sbin/iptables -A OUTPUT -m conntrack --ctstate INVALID -j DROP -m comment --comment "Drop Invalid OUTPUT Packets"
/sbin/iptables -A FORWARD -m conntrack --ctstate INVALID -j DROP -m comment --comment "Drop Invalid FORWARD Packets"
# Force Fragments packets check
/sbin/iptables -A INPUT -f -j DROP -m comment --comment "Force Fragments packets check"
# Reject spoofed packets
/sbin/iptables -A INPUT -i $EXTIF -s 169.254.0.0/16 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -s 172.16.0.0/12 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -s 127.0.0.0/8 -j DROP
#Multicast-adresses.
/sbin/iptables -A INPUT -i $EXTIF -s 224.0.0.0/4 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -d 224.0.0.0/4 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -s 240.0.0.0/5 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -d 240.0.0.0/5 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -s 0.0.0.0/8 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -d 0.0.0.0/8 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -d 239.255.255.0/24 -j DROP
/sbin/iptables -A INPUT -i $EXTIF -d 255.255.255.255 -j DROP
# SYN Flood Protection
/sbin/iptables -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -j syn_flood
/sbin/iptables -A syn_flood -p tcp -m tcp --tcp-flags FIN,SYN,RST,ACK SYN -m limit --limit 25/sec --limit-burst 50 -j RETURN
/sbin/iptables -A syn_flood -j DROP
##^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
# Allow HTTP to this Router
/sbin/iptables -A INPUT -i $INTIF -p tcp --dport 80 -j ACCEPT -m comment --comment "Accept HTTP from LAN"
# Allow SSH with brute-force attack protection from WAN
/sbin/iptables -A INPUT -i $EXTIF -p tcp -m tcp --dport $SSHPORT -m state --state NEW -m recent --set --name SSH_LIMIT --rsource
/sbin/iptables -A INPUT -i $EXTIF -p tcp --dport $SSHPORT -m state --state NEW -m recent --update --seconds 60 --hitcount 3 --name SSH_LIMIT --rsource -j DROP
/sbin/iptables -A INPUT -p tcp -m tcp --dport $SSHPORT -j ACCEPT -m comment --comment "Accept ssh from both WAN and LAN"
# DHCP client requests - accept from LAN
/sbin/iptables -A INPUT -i $INTIF -p udp --dport 67:68 -j ACCEPT -m comment --comment "Accept DHCP requests from LAN"
# Allow ping from LAN
iptables -A INPUT -i $INTIF -p icmp --icmp-type echo-request -j ACCEPT -m comment --comment "Accept Ping request from LAN"
iptables -A OUTPUT -o $INTIF -p icmp --icmp-type echo-reply -j ACCEPT -m comment --comment "Accept Ping reply to LAN"
if-up.d 部分，創建
/etc/network/if-up.d/my-post-up :
#!/bin/sh
EXTIF=eth0
if [ "$IFACE" = "$EXTIF" ]; then
/bin/sh /usr/myscripts/iptables/post-up-rules
fi
創建
/usr/myscripts/iptables/post-up-rules ：
#!/bin/sh
EXTIF=eth0
INTIF=br0
LOG=/tmp/set-rules-router.log
WANIP=$(/sbin/ifconfig $EXTIF | grep 'inet addr:' | cut -d: -f2 | awk '{ print $1}')
echo "POST-UP : `date`" | tee -a $LOG
echo "$IFACE post-up, $EXTIF IP : $WANIP" | tee -a $LOG
echo | tee -a $LOG
if [ -z "$WANIP" ]; then
exit;
fi
get_network(){
ip=$1
baseip=$(echo $ip | cut -d"." -f1-3)
echo $baseip".0"
}
LANIP=$(/sbin/ifconfig $INTIF | grep 'inet addr:' | cut -d: -f2 | awk '{ print $1}')
NETWORK=$(get_network "$LANIP")
PC2="10.0.1.130"; # Web server internal IP
MAIL="10.0.1.131"; # mail server internal IP
HTTPS_PORT=12310;
IMAPS_PORT=12311;
POP3S_PORT=12312;
## PORT FORWARDING vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
# HTTPS to Web Server
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport $HTTPS_PORT -j DNAT --to-destination $PC2:$HTTPS_PORT -m comment --comment "Port Forwarding to PC2"
/sbin/iptables -A FORWARD -p tcp -d $PC2 --dport $HTTPS_PORT -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $PC2/32 -p tcp -m tcp --dport $HTTPS_PORT -j SNAT --to-source $LANIP
# Mail Server
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport 25 -j DNAT --to-destination $MAIL:25 -m comment --comment "Port Forwarding SMTP"
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport 465 -j DNAT --to-destination $MAIL:465 -m comment --comment "Port Forwarding SMTPs"
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport 587 -j DNAT --to-destination $MAIL:587 -m comment --comment "Port Forwarding Submission"
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport $IMAPS_PORT -j DNAT --to-destination $MAIL:993 -m comment --comment "Port Forwarding IMAPs"
/sbin/iptables -t nat -A PREROUTING -d $WANIP -p tcp --dport $POP3S_PORT -j DNAT --to-destination $MAIL:995 -m comment --comment "Port Forwarding POP3s"
/sbin/iptables -A FORWARD -p tcp -d $MAIL -m multiport --dport 25,465,587,993,995 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $MAIL/32 -p tcp -m tcp --dport 25 -j SNAT --to-source $LANIP
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $MAIL/32 -p tcp -m tcp --dport 465 -j SNAT --to-source $LANIP
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $MAIL/32 -p tcp -m tcp --dport 587 -j SNAT --to-source $LANIP
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $MAIL/32 -p tcp -m tcp --dport 993 -j SNAT --to-source $LANIP
/sbin/iptables -A POSTROUTING -t nat -s $NETWORK/24 -d $MAIL/32 -p tcp -m tcp --dport 995 -j SNAT --to-source $LANIP
##^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
將以上四個腳本設為“可執行”： chmod +x filename。重啟 ...現在終于可以經這個路由上網了！
6. DDNS
我沒有固定 IP，所以要用 DDNS。我用的是 dnsexit（免費、收費都有），更新 DNS 非常簡單 - 在 /etc/rc.local 執行以下腳本就行。
/usr/myscripts/update-ddns
#!/bin/bash
USER=username;
PASSword=updatepassword;
DOMAINS=(domain1.net domain2.net); # multiple domains at the same IP separated by spaces
LOG=/tmp/update-ddns.log
echo "* $(date)" | tee -a $LOG
echo | tee -a $LOG
echo "Updating DDNS to dnsexit ..."
for domain in "${DOMAINS[@]}"; do
url="http://update.dnsexit.com/RemoteUpdate.sv?login=$USER&password=$PASSWORD&host=$domain";
echo $url | tee -a $LOG
result=$(curl -s $url)
echo "$result" | tee -a $LOG
echo | tee -a $LOG
done
echo | tee -a $LOG
當然要 chmod +x
/usr/myscripts/update-ddns 將這腳本設為“可執行”。
7. overlayroot
我們當然要求軟路由能經得起斷電而系統不壞，系統不會在我們不想改變的時候有任何變化。所以我使用了 overlayroot。
apt-get install overlayroot
其實上面的是不需要的，因為 Ubuntu 已經預裝了 overlayroot。
修改 /etc/overlayroot.conf，將 overlayroot="" 改為：
overlayroot="tmpfs"
重啟系統后，整個 root filesystem 已經被保護了。之后的任何改變，都會在重啟之后恢復回之前的狀態。
之后如果確實要改變系統，可以輸入 overlayroot-chroot 進入真實的檔案系統，然后修改 /etc/overlayroot.conf，改回 overlayroot=""，重啟 ... 這樣就停用了 overlayroot。
詳細可以參考：
https://spin.atomicobject.com/2015/03/10/protecting-ubuntu-root-filesystem/。
8. 其他腳本
我測試過把 WAN 口網線拔掉重插，if-pre-up.d 和 if-up.d 并沒有觸發。這就讓我擔心掉線之后會不會不能上網，或者 ip 改變導致 dns 和 port forwarding 規則失敗。其實最佳的解決辦法可能是用 ip monitor address 然后 grep，一直監視 WAN 口。但我在網上找到 ip monitor address 的例子非常少，而且也不知道怎樣改變地址來測試，所以只能用 cron。每隔 5分鐘或者10分鐘檢查一遍。
腳本不貼出來了，在附件里面。
other-scripts.zip
- vars ： 存儲 ping-sites 和 dns-check 兩個腳本通用的資料。
- ping-sites ： ping 一些外面的網站，第一次不通，ifdown && ifup；連續第二次不通，reboot。
- dns-check ： 比較 authoritative servers 和 WAN 口的 ip 地址，并且檢查 port forwarding 規則是不是含正確的 ip。
- send-mail ： 發送 email 的腳本。
9. WAN-to-LAN 速度測試
測試環境：
al@DESKTOP-CFK04JL:~$ iperf3 -c 10.0.0.133 -t 10
Connecting to host 10.0.0.133, port 5201
[ 4] local 10.0.1.29 port 41268 connected to 10.0.0.133 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 111 MBytes 929 Mbits/sec 0 731 KBytes
[ 4] 1.00-2.00 sec 110 MBytes 923 Mbits/sec 0 1.07 MBytes
[ 4] 2.00-3.00 sec 109 MBytes 912 Mbits/sec 0 1.07 MBytes
[ 4] 3.00-4.00 sec 110 MBytes 923 Mbits/sec 0 1.07 MBytes
[ 4] 4.00-5.00 sec 111 MBytes 933 Mbits/sec 0 1.07 MBytes
[ 4] 5.00-6.00 sec 109 MBytes 912 Mbits/sec 0 1.07 MBytes
[ 4] 6.00-7.00 sec 109 MBytes 912 Mbits/sec 0 1.07 MBytes
[ 4] 7.00-8.00 sec 108 MBytes 902 Mbits/sec 0 1.13 MBytes
[ 4] 8.00-9.00 sec 109 MBytes 912 Mbits/sec 0 1.13 MBytes
[ 4] 9.00-10.00 sec 109 MBytes 912 Mbits/sec 0 1.13 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 1.07 GBytes 917 Mbits/sec 0 sender
[ 4] 0.00-10.00 sec 1.06 GBytes 914 Mbits/sec receiver
iperf Done.
al@DESKTOP-CFK04JL:~$ iperf3 -c 10.0.0.133 -t 10
Connecting to host 10.0.0.133, port 5201
[ 4] local 10.0.1.29 port 41272 connected to 10.0.0.133 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 108 MBytes 906 Mbits/sec 0 1.04 MBytes
[ 4] 1.00-2.00 sec 110 MBytes 923 Mbits/sec 0 1.04 MBytes
[ 4] 2.00-3.00 sec 111 MBytes 933 Mbits/sec 0 1.04 MBytes
[ 4] 3.00-4.00 sec 110 MBytes 923 Mbits/sec 0 1.33 MBytes
[ 4] 4.00-5.00 sec 110 MBytes 923 Mbits/sec 0 1.33 MBytes
[ 4] 5.00-6.00 sec 111 MBytes 933 Mbits/sec 0 1.33 MBytes
[ 4] 6.00-7.00 sec 109 MBytes 912 Mbits/sec 0 1.33 MBytes
[ 4] 7.00-8.00 sec 111 MBytes 933 Mbits/sec 0 1.33 MBytes
[ 4] 8.00-9.00 sec 110 MBytes 923 Mbits/sec 0 1.33 MBytes
[ 4] 9.00-10.00 sec 110 MBytes 923 Mbits/sec 0 1.33 MBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 1.07 GBytes 923 Mbits/sec 0 sender
[ 4] 0.00-10.00 sec 1.07 GBytes 920 Mbits/sec receiver
iperf Done.
al@DESKTOP-CFK04JL:~$
WAN-to-LAN 速度 > 900 Mbits/sec，滿意！
sysctl.conf
部分設定是希望增加 Network throughput 的，可是測試過，沒看到區別。
部分設定是增加安全的（參考了一些網頁，還有 ipcop, clearOS, debian 等系統）。
因為 sysctl.conf 已經設置了，所以 1樓的
/usr/myscripts/iptables/pre-up-rules 可以去掉下面幾行：
# Ref : https://wiki.debian.org/DebianFirewall
#echo -n '1' > /proc/sys/net/ipv4/ip_forward
#echo -n '0' > /proc/sys/net/ipv4/conf/all/accept_source_route
#echo -n '0' > /proc/sys/net/ipv4/conf/all/accept_redirects
#echo -n '1' > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
#echo -n '1' > /proc/sys/net/ipv4/icmp_ignore_bogus_error_responses
#
# /etc/sysctl.conf - Configuration file for setting system variables
# See /etc/sysctl.d/ for additional system variables.
# See sysctl.conf (5) for information.
#
#kernel.domainname = example.com
# Uncomment the following to stop low-level messages on console
#kernel.printk = 3 4 1 3
##############################################################3
# Functions previously found in netbase
#
# Uncomment the next two lines to enable Spoof protection (reverse-path filter)
# Turn on Source Address Verification in all interfaces to
# prevent some spoofing attacks
#net.ipv4.conf.default.rp_filter=1
#net.ipv4.conf.all.rp_filter=1
# Uncomment the next line to enable TCP/IP SYN cookies
# See http://lwn.net/Articles/277146/
# Note: This may impact IPv6 TCP sessions too
#net.ipv4.tcp_syncookies=1
# Uncomment the next line to enable packet forwarding for IPv4
net.ipv4.ip_forward=1
# Uncomment the next line to enable packet forwarding for IPv6
# Enabling this option disables Stateless Address Autoconfiguration
# based on Router Advertisements for this host
#net.ipv6.conf.all.forwarding=1
###################################################################
# Additional settings - these settings can improve the network
# security of the host and prevent against some network attacks
# including spoofing attacks and man in the middle attacks through
# redirection. Some network environments, however, require that these
# settings are disabled so review and enable them as needed.
#
# Do not accept ICMP redirects (prevent MITM attacks)
#net.ipv4.conf.all.accept_redirects = 0
#net.ipv6.conf.all.accept_redirects = 0
# _or_
# Accept ICMP redirects only for gateways listed in our default
# gateway list (enabled by default)
# net.ipv4.conf.all.secure_redirects = 1
#
# Do not send ICMP redirects (we are not a router)
#net.ipv4.conf.all.send_redirects = 0
#
# Do not accept IP source route packets (we are not a router)
#net.ipv4.conf.all.accept_source_route = 0
#net.ipv6.conf.all.accept_source_route = 0
#
# Log Martian Packets
#net.ipv4.conf.all.log_martians = 1
#
# disable ipv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
net.ipv6.conf.lo.disable_ipv6 = 1
net.ipv6.conf.eth0.disable_ipv6 = 1
# https://easyengine.io/tutorials/linux/sysctl-conf/
### IMPROVE SYSTEM MEMORY MANAGEMENT ###
# Increase size of file handles and inode cache
fs.file-max = 2097152
# Do less swApping
vm.swappiness = 5
vm.dirty_ratio = 60
vm.dirty_background_ratio = 2
### GENERAL NETWORK SECURITY OPTIONS ###
# Number of times SYNACKs for passive TCP connection.
net.ipv4.tcp_synack_retries = 2
# Allowed local port range
net.ipv4.ip_local_port_range = 2000 65535
# Protect Against TCP Time-Wait
net.ipv4.tcp_rfc1337 = 1
# Decrease the time default value for tcp_fin_timeout connection
net.ipv4.tcp_fin_timeout = 15
# Decrease the time default value for connections to keep alive
net.ipv4.tcp_keepalive_time = 300
net.ipv4.tcp_keepalive_probes = 5
net.ipv4.tcp_keepalive_intvl = 15
### TUNING NETWORK PERFORMANCE ###
# Default Socket Receive Buffer
net.core.rmem_default = 31457280
# Maximum Socket Receive Buffer
net.core.rmem_max = 12582912
# Default Socket Send Buffer
net.core.wmem_default = 31457280
# Maximum Socket Send Buffer
net.core.wmem_max = 12582912
# Increase number of incoming connections
net.core.somaxconn = 4096
# Increase number of incoming connections backlog
net.core.netdev_max_backlog = 65536
# Increase the maximum amount of option memory buffers
net.core.optmem_max = 25165824
# Increase the maximum total buffer-space allocatable
# This is measured in units of pages (4096 bytes)
net.ipv4.tcp_mem = 65536 131072 262144
net.ipv4.udp_mem = 65536 131072 262144
# Increase the read-buffer space allocatable
net.ipv4.tcp_rmem = 8192 87380 16777216
net.ipv4.udp_rmem_min = 16384
# Increase the write-buffer-space allocatable
net.ipv4.tcp_wmem = 8192 65536 16777216
net.ipv4.udp_wmem_min = 16384
# Increase the tcp-time-wait buckets pool size to prevent simple DOS attacks
net.ipv4.tcp_max_tw_buckets = 1440000
net.ipv4.tcp_tw_recycle = 1
net.ipv4.tcp_tw_reuse = 1
# Additional setting with reference to ipcop/clearos
net.ipv4.ip_dynaddr = 1
# rp_filter = 1, source address verification helps protect against spoofing attacks
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.default.accept_redirects = 0
net.ipv4.conf.default.send_redirects = 0
net.ipv4.conf.default.accept_source_route = 0
#net.ipv4.conf.default.log_martians = 1
net.ipv4.conf.default.promote_secondaries = 1
net.ipv4.conf.all.rp_filter = 1
net.ipv4.conf.all.accept_redirects = 0
net.ipv4.conf.all.send_redirects = 0
net.ipv4.conf.all.accept_source_route = 0
#net.ipv4.conf.all.log_martians = 1
net.ipv4.conf.all.promote_secondaries = 1
# also suggested by Debian
net.ipv4.icmp_echo_ignore_broadcasts = 1
net.ipv4.icmp_ignore_bogus_error_responses = 1
目前就做成這樣，先用一段時間看看有什么要修改的。
